info@arraystarled.com
Email Us
WS2815 IC Built-in SPI LED Strip ART-5050IC2815-60-RGB-12
- Model:ART-5050IC2815-60-RGB-12
- LED Type:SMD 5050
- LED Qty/M:60
- Voltage:12V DC
- Power W/m:12W/m
- CCT/Color:Magic RGB
- CRI:/
- Dimension:10mm
- Warranty:3 Years
Technical Specifications
| Model | ART-5050IC2815-60-RGB-12 |
|---|---|
| LED Type | SMD 5050 |
| LED Qty/m | 60 |
| Voltage | 12V DC |
| Power (W/m) | 12W/m |
| CCT/Color | Magic RGB |
| CRI | / |
| Dimension | 10mm |
| Warranty | 3 Years |
| Material | |
| Package | |
| Minimum Order Quantity | Factory-direct - on request |
| Certifications | CE, RoHS |
Product Description
For addressable color projects that have to keep running if one pixel fails, I use WS2815 rather than the older 5V WS2812. This 10mm board runs 60 LEDs/m on 12V DC at about 12W/m, with the WS2815 IC built into each 5050 package and a backup data line that passes signal around a dead pixel.
Why WS2815 over WS2812
Two practical reasons. It's 12V, so voltage drop over a run is far less of a headache than 5V, and the chip has a dual-data (backup) line — if one pixel is damaged, signal still reaches the LEDs after it instead of the whole tail going dark. It uses the same clock-less one-wire data timing most SPI controllers already speak, so code is straightforward.
Key Features
- WS2815 IC, individually addressable RGB
- 12V operation with backup data line for fault tolerance
- 60 LEDs/m, 5050 package, about 12W/m
- Works with common SPI pixel controllers (SP107E, K1000C, Arduino, etc.)
- Standard 10mm footprint
Typical Applications
- Large pixel installs where reliability matters
- Signage, lettering, and logo outlines
- Stage, bar, and game-room lighting
- Long 12V runs where 5V would drop off
Specifications
| Parameter | Value |
|---|---|
| Model | ART-5050IC2815-60-RGB-12 |
| IC / LED | WS2815 / SMD 5050 |
| LED quantity | 60 LEDs/m |
| Power | ~12 W/m |
| Voltage | 12V DC |
| Control | Single-wire data + backup line |
| PCB width | 10 mm |
| Warranty | 3 years |
Installation notes
- Mind the arrow — data flows one way; connect DIN from the controller, not DOUT.
- Inject 12V at both ends on runs over 5m and add a common ground between controller and strip.
- Use a 12V supply rated for ~12W/m plus 20% headroom.
- For the backup feature, wire the second data line as your controller supports it.
Frequently Asked Questions
Can I just swap it for WS2812?
Not directly — WS2815 runs on 12V and has a backup data pin. The data timing is similar, but power and wiring differ.
What happens if one LED burns out?
With the backup data line connected, the signal bypasses the bad pixel and the rest of the run keeps working.
How many LEDs can one controller drive?
That depends on the controller's refresh speed; for large counts use an SPI controller with enough memory and split into parallel data lines.
Can I order custom specifications or OEM branding?
Yes. As the manufacturer we support custom lengths, colour temperature, CRI, packaging and OEM labeling; send us your specification.
Can I request a sample before a bulk order?
Yes, samples are available so you can confirm the colour, build and output before a bulk order. Request a sample through our contact page.